Recent content by shwnwllms
-
ZMF Pendant by Ampsandsound; impressions, tube-rolling, and general discussions
There is a whole thread dedicated to the Reserve. It was the flavor of the month a few months back- shwnwllms
- Post #2,534
- Forum: Headphone Amps (full-size)
-
ZMF Pendant by Ampsandsound; impressions, tube-rolling, and general discussions
Same. I felt the it wasn’t doing the Caldera justice and they are certainly less power hungry than a Sus I don’t think it will drive the Tungsten or Sash Tre either. Bigger Ben would be suitable for all three.- shwnwllms
- Post #2,526
- Forum: Headphone Amps (full-size)
-
Comment by 'shwnwllms' on listing 'ZMF Atrium Closed in walnut'
Beautiful set. Can confirm the Walnut AC is “snappier” & “airier” as I own a Marblecake Walnut AC. This set is going to make someone very happy GLWS!!!- shwnwllms
- Comment
-
HQPlayer Impressions and Settings Rolling Thread
It’s a bug, it will be fixed in a future update. This is the workaround until then- shwnwllms
- Post #1,361
- Forum: Computer Audio
-
HQPlayer Impressions and Settings Rolling Thread
Change DSP pipelines to 8- shwnwllms
- Post #1,359
- Forum: Computer Audio
-
HQPlayer Impressions and Settings Rolling Thread
Plenty of DACs only support 44.1 kHz (it’s cheaper to manufacture that way as you have to have a separate pathway for 48 kHz so it cuts down on components etc)- shwnwllms
- Post #1,353
- Forum: Computer Audio
-
HQPlayer Impressions and Settings Rolling Thread
If your DAC supports it check adaptive output rate and 48 kHz so you stay within the rate family which will be less resource intensive- shwnwllms
- Post #1,351
- Forum: Computer Audio
-
ampsandsound (aka Amps & Sound)
Thank you Justin, this is very helpful. One question for you, what would you consider optimal input voltage on an amp that has the step up transformer like the Agartha?- shwnwllms
- Post #1,257
- Forum: Headphone Amps (full-size)
-
What Are You Listening To Right Now?
Sam Beam and Fiona Apple are perfection -
HQPlayer Impressions and Settings Rolling Thread
Give Sinc-MGa if you haven’t already (Gauss version of Sinc-M)- shwnwllms
- Post #1,334
- Forum: Computer Audio
-
HQPlayer Impressions and Settings Rolling Thread
Could have been the IPv6 if you made that change as well. I just tested setting the input/output field to both NAA at the same time and @bogi is correct, this shouldn't cause an issue.- shwnwllms
- Post #1,322
- Forum: Computer Audio
-
HQPlayer Impressions and Settings Rolling Thread
You're welcome, good news is it's working now, and plenty of knowledgeable people here to help you troubleshoot if something breaks. Now you can tweak it as much or little as you like. Have fun trying the different filters and modulators / dithers. You asked earlier about filter recommendations...- shwnwllms
- Post #1,318
- Forum: Computer Audio
-
HQPlayer Impressions and Settings Rolling Thread
I had a feeling that might be the culprit. Basically there was a conflict in the settings since you had NAA set as both input and output device initially. IIRC I made the same mistake when I initially set up my NAA- shwnwllms
- Post #1,316
- Forum: Computer Audio
-
HQPlayer Impressions and Settings Rolling Thread
NAA should be hardwired, I was never able to get it an NAA to work reliably over WiFi even at lower rates. Someone smarter than me can chime in here but I believe it has something to do with latency.- shwnwllms
- Post #1,313
- Forum: Computer Audio