Recent content by dmance
-
CHORD ELECTRONICS DAVE
You misread my reply. All your other points are good solutions ...but in respect to the wire from the DAC output to the other downstream components...you need to stop RF noise from coming BACK up that wire. Some DACs use a low pass filter or transformer at the output but this takes away...- dmance
- Post #24,567
- Forum: High-end Audio Forum
-
CHORD ELECTRONICS DAVE
Any downstream RF noise from the amplifier AC Mains connection or EM induced thru the speaker leads ...all this permeates to any galvanic connection. So the DAC RCA outputs are also galvanically connected to this mess....and hence the DAC innards as well. Small subtle impact on the circuits...- dmance
- Post #24,562
- Forum: High-end Audio Forum
-
CHORD ELECTRONICS DAVE
Before you assume there is some kind of magic going on ...Consider that the preamp is in the DACs output path. Ask yourself... if Dave has volume that is nigh perfect...noise shaped too ....and the output is not stressed due to it going into a high impedance...then how does adding a pre in the...- dmance
- Post #24,559
- Forum: High-end Audio Forum
-
Hugo M Scaler by Chord Electronics - The Official Thread
That 'somehow' that's degrading a sound is that your source is a generator of RF noise ...that is the digital logic sets off MHz/Ghz energy that travels back up the power cables or any metal signal cables or even via the chassis itself. The whole chain then acts like a big antenna and path to...- dmance
- Post #10,263
- Forum: High-end Audio Forum
-
Hugo M Scaler by Chord Electronics - The Official Thread
Any metal appendage is an antenna. Signal or power. Shielding helps but rfi is insidious & incredulous ...but it travels meters in open air to impinge on a dac and show up at the output jacks. Yes, rfi is well outside the audio band but its mere presence in the conductor/dielectric path affects...- dmance
- Post #10,228
- Forum: High-end Audio Forum
-
Chord Electronics - Hugo 2 - The Official Thread
I was exhibiting at CanJam NYC with my wares RF optimizing both a Hugo2 and TT2 through a similar HQPlayer setup. I had Utopia and HE1000se headphones available and in the quiet before the attendees showed up I had a good listen to both. I must say that the Hugo2 sounded incredibly good - even...- dmance
- Post #18,152
- Forum: Portable Source Gear
-
Hugo M Scaler by Chord Electronics - The Official Thread
I was at CanJam NYC (first show plying my wares) and sat through both of Rob Watt's talks and he came to my stand for a chat. In his presentation, he provided good in-depth technical information, however my takeaway was the incredulity of the level of resolution being strived for. Rob is not...- dmance
- Post #10,145
- Forum: High-end Audio Forum
-
Hugo M Scaler by Chord Electronics - The Official Thread
You don't need reclocking. Mscaler reclocks and then all chord DACs reclock again. Modern DACs are immune to variations in upstream timing. If you hear a difference ...there is another mechanism at play- dmance
- Post #10,084
- Forum: High-end Audio Forum
-
Hugo TT 2 by Chord Electronics - The Official Thread
Drawing attached. Either of these will work. Presumably the interconnect has some level of shielding via the DAC's ground. However my cable guy says that the issue with using interconnects for driving speaker loads is the thinner gauge wire used limits the frequency response with higher...- dmance
- Post #8,454
- Forum: High-end Audio Forum
-
Hugo TT 2 by Chord Electronics - The Official Thread
This is great ...time for me to try XLR!. So what is the wiring diagram,then?- dmance
- Post #8,424
- Forum: High-end Audio Forum
-
Hugo TT 2 by Chord Electronics - The Official Thread
I've never touched the balanced XLR outputs. I know the single ended RCA's are just a direct lead from Rob's pulse array output (well via a hi/low gain relay). My understanding is balanced just takes this to an amplifier stage to create a negative going signal. So you have ~twice the power but...- dmance
- Post #8,421
- Forum: High-end Audio Forum
-
Hugo TT 2 by Chord Electronics - The Official Thread
FYI, I have DIY voxativs and recently adjusted my TT2 to low gain mode (from high gain). Big difference in SQ. I play music as loudly but I notice it's more transparent.- dmance
- Post #8,416
- Forum: High-end Audio Forum
-
Hugo M Scaler by Chord Electronics - The Official Thread
Dual-BNC is maxed out at 768kHz sample rate (at 24bits) due to S/PDIF being the technology underpinnings. I like the separation of digital upsampling from D/A and MScaler sets a benchmark for how good digital audio can sound. As far as 2020 products, I'd like to see: - the digital amps (whats...- dmance
- Post #9,971
- Forum: High-end Audio Forum
-
CHORD ELECTRONICS DAVE
Go to your dealer. As has been mentioned on this forum and other communications i've read, some newer Dave units are problematic (a component change, i think). Definitely, with factory (or non exotic) coax cables, this should not happen.- dmance
- Post #13,952
- Forum: High-end Audio Forum
-
Chord Electronics - Hugo 2 - The Official Thread
If your are running Windows10, its native USB Audio 2.0 so any Chord DAC is plug-and-play WASAPI 'exclusive-mode' without driver install.- dmance
- Post #17,886
- Forum: Portable Source Gear