etc6849

etc6849

100+ Head-Fier From Columbia, SC
Joined
Last seen
Messages
217
Reaction score
213
Medals
0
Classifieds feedback

Latest activity Postings Classifieds listings Classifieds feedback Head Gear Reviews About

    • etc6849
      etc6849 reacted to aokman's post in the thread The Stax Thread III with Like Like.
      How you take measurements will also significantly affect readings, here is a new prototype Lundahl LL1630 setup, floating single probe...
    • etc6849
      etc6849 reacted to aokman's post in the thread Stax SR-X9000 with Like Like.
      Most noise is already in your conductor wires and introduced from other devices on the same wire runs back feeding into your house...
    • etc6849
      etc6849 reacted to aokman's post in the thread Stax SR-X9000 with Like Like.
      A power cable makes no difference lol, let alone on something so low powered… Open your amp up if you want to see the “boutique” normal...
    • etc6849
      etc6849 replied to the thread The Stax Thread III.
      If they do come out with a Stax X9000 successor, used prices will go down a bunch. This will be great for anyone looking to try the...
    • etc6849
      etc6849 reacted to aokman's post in the thread The Stax Thread III with Like Like.
      Lundahl LL1630PP is basically dead flat from 20Hz to 30Khz, directly driven with no resistors or compensation, up to about 300Vrms where...
    • etc6849
      etc6849 reacted to gammi's post in the thread The Stax Thread III with Like Like.
      Time to see how the X9000 likes 200W of vintage Japanese powahhhh (Yes, my adapter circuit still looks like crap, don't judge lol)
    • etc6849
      etc6849 replied to the thread The Stax Thread III.
      https://www.avmentor.net/reviews/2016/benchmark_dac2hgc_ahb2_2.shtml It looks like it is 16V/uS, but probably in stereo mode so should...
      • 1713755388851.png
    • etc6849
      etc6849 reacted to aokman's post in the thread The Stax Thread III with Like Like.
      Yeah good to hear, I almost went the bias transformer route as that works also but cost the same in the end due to shipping etc so went...
    • etc6849
      etc6849 replied to the thread The Stax Thread III.
      I measured them both ~1000V at 1kHz with a 120pF load to simulate the headphones. Did you measure the Sansui in your transformer setup...
    • etc6849
      etc6849 reacted to aokman's post in the thread The Stax Thread III with Like Like.
      Like I said, hearsay and mudslinging everywhere you look… I can get a Carbon from myheadfi locally way cheaper but then immediately hit...
    • etc6849
      etc6849 reacted to gammi's post in the thread The Stax Thread III with Like Like.
      I back to back compared my Lundahl transformer circuit with my DVA M225 monoblocks (review here) vs a $15k DIY T2... and I preferred the...
    • etc6849
      etc6849 reacted to Chefguru's post in the thread The Stax Thread III with Like Like.
      The transformer box situation is not that controversial. A well made Lundahl transformer box is $1500~ and the cost of a proper speaker...
    • etc6849
      etc6849 replied to the thread The Stax Thread III.
      Could be, but I need to have someone in South Carolina bring one by for me to try out. There needs to be a measurable improvement too...
    • etc6849
      etc6849 replied to the thread The Stax Thread III.
      This is what I had a picture of from before when I was comparing the two; while feeding each from a signal generator. Note the small...
      • 1713733912503.jpeg
      • 1713733952585.jpeg
    • etc6849
      etc6849 reacted to Tachikoma's post in the thread The Stax Thread III with Like Like.
      Have you actually tried a decent transformer box (not an srd-6 or srd-7)? I owned a kgsshv carbon and tbh, the transformer box + amp was...
    Show older items
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…
Back
Top