Recent content by robrob
-
HE-500 Broken Headband & Fix
Yes, I'm very glad I changed my mind and took my 500s out of the trash and installed the HE-400i band.- robrob
- Post #5
- Forum: Headphones (full-size)
-
HE-500 Broken Headband & Fix
I've put a lot of time on the new 400i headband and I absolutely love the upgrade. The band is much more comfortable but the real bonus is the extra clamping force which gives me much more refined low bass. This is a fantastic upgrade.- robrob
- Post #2
- Forum: Headphones (full-size)
-
Schiit Gungnir DAC
I received my Gungnir back from Schiit today for the multibit upgrade. I already had the Gen 5 USB. I had to wait about two weeks in the upgrade que and Schiit received it on 14 February and I received it 2 March. Total with tax and shipping for the multibit upgrade was $580. It's paired with a...- robrob
- Post #5,993
- Forum: Dedicated Source Components
-
Schiit Gungnir DAC
Schiit's turnaround time for the Gungnir Multibit upgrade has been slow. I had to wait about 2 weeks in the que to ship my unit. They received it 14 Feb and I was notified today (24 Feb) that they are ready to ship it out.- robrob
- Post #5,989
- Forum: Dedicated Source Components
-
HE-500 Broken Headband & Fix
I'm wondering how common is it for the HE-500 headband to break? I ask because I used one hand to remove my HE-500s a couple of weeks ago and the round plastic clamp that holds the earcup slider broke in half. It's not like I pulled really hard or did anything strange when removing the...- robrob
- Thread
- Replies: 4
- Forum: Headphones (full-size)
-
Schiit Gungnir DAC
The Gungnir multi-bit upgrade is pretty popular. I'm currently # 3 of 37 in the que for upgrade. I did the Gen 5 USB upgrade last year so I'm not doing the Unison USB.- robrob
- Post #5,976
- Forum: Dedicated Source Components
-
Tripath TA2024 Amp Board as Balanced Headphone Amp in TEAC UD-H01 DAC
The little amp is still going strong and all my balanced headphones run fine with it.- robrob
- Post #5
- Forum: Headphone Amps (full-size)
-
Schiit Mjolnir 2 Amp / Tube Rolling
I just upgraded from a Mjolnir 1 to a 2 because I'm a tube guy. I design, build and repair guitar tube amplifiers and I love tube audio. I fired up the MJ2 last night and was disappointed. It seemed I lost some clarity compared to the the solid state MJ1. I let it burn in overnight but the tone...- robrob
- Post #27
- Forum: Headphone Amps (full-size)
-
Schiit Gungnir DAC
I bought an early model Gungnir a few years ago and I've always had to use the S/PDIF input because the USB was flakey. Sometimes the USB would work and then it would just disappear and my Win 10 computer wouldn't recognize it. For the last year or so I got a "unrecognized device" error when...- robrob
- Post #5,892
- Forum: Dedicated Source Components
-
Calling All "Vintage" Integrated/Receiver Owners
The 180 and 330 ohm resistors form a voltage divider to cut the output signal voltage by 35% or 17dB. The load impedance the amp sees is also affected by the resistors. With 32 ohm headphones the load would be 209 ohms so way above the typical 4 to 16 ohm speaker load but solid state amps are ok...- robrob
- Post #17,802
- Forum: Headphone Amps (full-size)
-
DIY HE Adapter
Mightygrey, that sounds correct.- robrob
- Post #46
- Forum: DIY (Do-It-Yourself) Discussions
-
Calling All "Vintage" Integrated/Receiver Owners
Reel-to-reel will offer much better fidelity and signal-to-noise ratio compared to cassette and they look much cooler too.- robrob
- Post #17,472
- Forum: Headphone Amps (full-size)
-
Calling All "Vintage" Integrated/Receiver Owners
25dB of attenuation is a good place to start. Your resistor values look good. Here's the basic attenuator layout:- robrob
- Post #17,463
- Forum: Headphone Amps (full-size)
-
Calling All "Vintage" Integrated/Receiver Owners
I have HE-500 and Senn HD 6XX cans but my modified and balanced Fostex T50RPs sound best to me when driven by speaker amps. As Guido mentioned, the biggest difference is the solid, hard hitting bass response.- robrob
- Post #17,384
- Forum: Headphone Amps (full-size)
-
Calling All "Vintage" Integrated/Receiver Owners
The box has a bypass switch that makes a direct connection. I can run direct or with attenuation. There's also a switch to allow balanced and unbalanced headphones to run on balanced and unbalanced amp outputs. Typically solid state amps run headphones fine with a direct connection but tube...- robrob
- Post #17,381
- Forum: Headphone Amps (full-size)